Go Back   CMP Forums > CMP General > Ask Each Other > Reloading
Register FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
  #21  
Old 03-04-2017, 08:38 AM
The Original Youngblood The Original Youngblood is offline
 
Join Date: May 2010
Location: Virginia, on the west side of my ancestral farm
Posts: 740
Default

My standard for .45acp 230gr FMJ is 5.0gr of Bullseye with a COAL of ~1.25".

It runs ~815fps in my 5" 45s and is very accurate.

From what I have read, this duplicates the original military load.

Enjoy!
__________________
Original Join Date: 25Mar04
Reply With Quote
  #22  
Old 03-04-2017, 09:44 AM
a31b20 a31b20 is online now
 
Join Date: Oct 2009
Location: California
Posts: 423
Default

If you are not Locked into using 230 gr bullets try using a 185 gr plated bullet.
I have had good luck with the Berrys 185 hollow base Rn or the Extreme 185 gr Flat point...mild recoil and accurate.
Bullseye or Win 231 works well,have been using 231 of late with CCI large pistol primer..1.250 OAL ...light crimp using the Lee factory crimp die( also sizes the case back to factory specs at the same time) Brass seems to last forever..I lose it before it wears out.


Have fun, Rich
Reply With Quote
  #23  
Old 03-04-2017, 11:17 AM
aimit aimit is offline
 
Join Date: Oct 2009
Posts: 2,169
Default

HP 38 and W231 are now the same powder, made by the same company, sometimes even having the same lot number and is very good powder for 45ACP. AA#5 is also OK but requires more powder per round.

Last edited by aimit; 03-04-2017 at 11:19 AM.
Reply With Quote
  #24  
Old 03-04-2017, 01:55 PM
ww2farmer ww2farmer is offline
 
Join Date: Feb 2013
Location: USA
Posts: 305
Default

I load 45acp for two 1911's (both 5" full size), and two Smith and Wesson M&P 45's (one full size, one Shield)

230 grain plated round nose is all I use, and it's usually with 4.7 grains of Bullseye, seated to 1.250", with mixed brass, mixed large pistol primers, and a firm but not excessive taper crimp. 100% reliably cycling load in all those pistols, soft shooting, and as accurate as I am at handgun plinking range
Reply With Quote
  #25  
Old 03-04-2017, 03:23 PM
jmm jmm is online now
 
Join Date: Sep 2010
Location: G'Boro, NC
Posts: 1,704
Default

I've used Win 231 (or HP-38) for years. Switched to the Berry's 185gr Hollow Base Round Nose also, but this probably aren't legal for Service Matches.
Look for HP-38 over Win 231, it is usually $1 less per pound around here.
Win 231/HP-38 was unavailable during the shortage, I started with Titegroup. I was at the Greensboro Gunshow when one of the sellers brought in the the first shipment of Win 231. The other sellers reduced their price of Titegroup immediately, and I picked up several 1# bottles for less than $19 each.
__________________
Life, liberty and the pursuit of happiness are God given rights, not government granted rights.
Reply With Quote
  #26  
Old 03-05-2017, 06:44 AM
grumpa72 grumpa72 is offline
 
Join Date: Apr 2010
Location: Moon Township, PA
Posts: 1,792
Default

Win 231/HP38 either 4.9 or 5.3 grains under a 230 bullet either lead or copper plated (thinner than copper jacket and cheaper but still acts like a fmj). I do them 500 at a time and try to always keep 1000 +/- on my shelf.
Reply With Quote
  #27  
Old 03-05-2017, 08:54 PM
plattincreek plattincreek is offline
 
Join Date: Oct 2009
Location: Just south of St. Louis, Mo.
Posts: 253
Default

My Colt Government Model has had a steady diet of cast 230 grain lead RN bullets over 5.0 grains of Bullseye for years and years. Perhaps not as hard as jacketed bullets but they still work just fine in my 1911.
Reply With Quote
  #28  
Old 03-08-2017, 12:54 PM
Pinecone Pinecone is offline
 
Join Date: Jan 2014
Posts: 483
Default

I started with Bullseye, as a cheap college student. But found it very dirty, so switched to Unique.

Loaded that for MANY years, then switched to WW231. And have loaded that primarily for a lot of years.

I have some Clays to try for lower recoil loads for PA Steel Shoot matches.
Reply With Quote
  #29  
Old 03-15-2017, 11:07 PM
medalguy medalguy is offline
 
Join Date: Oct 2009
Location: New Mexico
Posts: 1,170
Default

Bullseye 5.0 gr for 230 gr FMJ has been pretty much the standard for oh, about 100 years.
Reply With Quote
  #30  
Old 03-16-2017, 06:29 AM
bernie bernie is offline
 
Join Date: Oct 2009
Location: Arkansas
Posts: 171
Default

One of the things I like about loading for the .45 ACP is that there are so many options. I currently load 230 grain loads using HP38/Win231, but I have used lots of other powders. I have like those mentioned so far, but I have also had good results with Power Pistol.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 06:26 PM.