Go Back   CMP Forums > CMP Sales > Smallbore
Register FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 06-21-2018, 12:51 PM
olddude olddude is offline
 
Join Date: Jul 2011
Location: Missouri
Posts: 59
Default Scope barrel mounts Remington 513T?

Been searching with no luck. Can anyone tell me what part numbers or make these were and where they might be obtained?

My gun is tapped and want to try a Lyman 438 on it.

Any help appreciated.
Reply With Quote
  #2  
Old 06-22-2018, 06:54 AM
schutzen-jager schutzen-jager is offline
 
Join Date: Oct 2009
Location: peoples republic of n.j.
Posts: 504
Default

try steve earl - he used to sell them ---www.steveearleproducts.com/scopeblocks.html

Last edited by schutzen-jager; 06-22-2018 at 06:10 PM. Reason: addendum
Reply With Quote
  #3  
Old 06-27-2018, 07:03 PM
Herschel Herschel is offline
 
Join Date: Oct 2010
Location: Rison, AR
Posts: 617
Default

A list of applications for scope blocks by Unertl shows the correct blocks are
an "A" and an "L" for the Remington 513T. It appears that Lyman and Unertl used he same codes for their scope blocks.
Reply With Quote
  #4  
Old 06-27-2018, 07:51 PM
olddude olddude is offline
 
Join Date: Jul 2011
Location: Missouri
Posts: 59
Default Thank you sir!!

As always a fine gentleman with generous sharing of good information.

I do appreciate it!
Reply With Quote
  #5  
Old 08-27-2018, 06:52 PM
navyrifleman navyrifleman is offline
 
Join Date: Nov 2009
Posts: 95
Default

The original Remington 513T rifles were drilled and tapped for long tube scopes - which were adjusted externally by turning screws in the rings themselves.

513T's made in later years (up to 1969) had grooved receivers which would accept the more modern .22 type scopes.

One of mine is of this type, made in 1966. Using a cheap Tasco scope on it, I have introduced my sons and grandsons to rifle shooting. It is very accurate, and that makes it a great instruction rifle, because mistakes are easily identified and corrected.
Reply With Quote
  #6  
Old 08-27-2018, 08:43 PM
mac1911 mac1911 is offline
 
Join Date: Oct 2009
Posts: 2,722
Default

If your not looking to stay traditional try to find one of these
Ken Viani mount ken1855@hotmail.com i dont think he makes them anymore. It bolts to the rear scope block mount and the rear match sight holes.
Reply With Quote
  #7  
Old 08-27-2018, 10:55 PM
edlmann edlmann is offline
 
Join Date: Oct 2009
Location: lovely downtown Central Florida
Posts: 4,845
Default

Quote:
Originally Posted by mac1911 View Post
If your not looking to stay traditional try to find one of these
Ken Viani mount ken1855@hotmail.com i dont think he makes them anymore. It bolts to the rear scope block mount and the rear match sight holes.
__________________
I love the smell of MRT in the morning - it reminds me of . . . wet canvas."

I'm what you'd call a legend in my own mind.

2071 posts on the old forum - not that I'm counting . . .
Reply With Quote
  #8  
Old 09-24-2018, 04:37 PM
lyman lyman is offline
 
Join Date: Oct 2009
Posts: 88
Default

Quote:
Originally Posted by Herschel View Post
A list of applications for scope blocks by Unertl shows the correct blocks are
an "A" and an "L" for the Remington 513T. It appears that Lyman and Unertl used he same codes for their scope blocks.
do they list the heights?

not all the mounts out there are marked with letters, some have the heights (like .125) and some are not marked at all, so you would have to measure,


438's are a nice scope,

I have an older 5a (or is it A5) and a spot, target spot and super target spot,
Reply With Quote
  #9  
Old 11-03-2018, 01:42 PM
motorcop motorcop is offline
 
Join Date: Dec 2010
Location: Southeast Wisconsin
Posts: 541
Default

The Unertl "A" block is .910" long X .175" high, with .562" hole spacing.

Unertl "L" block is 1.250" long X .175" high, with .850" hole spacing.

Make sure to check the hole spacing on your specific rifle as sometimes they can be different.

Rick H.
Reply With Quote
  #10  
Old 11-03-2018, 08:35 PM
edlmann edlmann is offline
 
Join Date: Oct 2009
Location: lovely downtown Central Florida
Posts: 4,845
Default

Quote:
Originally Posted by motorcop View Post
The Unertl "A" block is .910" long X .175" high, with .562" hole spacing.
Unertl "L" block is 1.250" long X .175" high, with .850" hole spacing.
Make sure to check the hole spacing on your specific rifle as sometimes they can be different.
Double check screw thread - Steve Earle says your threads may be 6-44 instead of 6-48.
__________________
I love the smell of MRT in the morning - it reminds me of . . . wet canvas."

I'm what you'd call a legend in my own mind.

2071 posts on the old forum - not that I'm counting . . .
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:33 PM.