Go Back   CMP Forums > Welcome Center > How To's
Register FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 06-10-2014, 08:30 PM
Aladinbama Aladinbama is offline
 
Join Date: Nov 2009
Location: Pearland, Tx
Posts: 126
Send a message via AIM to Aladinbama
Default How To: Oil scrub videos

For those who may be interested in how to do an oil scrub to clean a stock, I've done a few videos to basically show how it is done and what is is done with.
For those wondering, this is probably the most frequently asked question in regards to my products; What do I do to clean my stock? This is not by any means the end all, but it is a tried and proven way to "see what you have" so to speak.
Materials needed;
https://www.youtube.com/watch?v=lJCy-DL0uh0
The oil scrub itself;
https://www.youtube.com/watch?v=Z0NeRwpZKwc
And After the scrub;
https://www.youtube.com/watch?v=i27HWD_UiDw

Again, this is the one way I recommend most for the initial cleaning of a dirty gunstock. After a couple of these you can then decide how you may want to proceed.
Thanks, Tom
__________________
Please Visit My Web Page
www.thegunstockdoctor.com
Reply With Quote
  #2  
Old 07-29-2014, 08:19 PM
MixedBreed MixedBreed is offline
 
Join Date: Feb 2014
Posts: 199
Default

Tom, you use turpentine for your 50/50 scrub mix, but would mineral spirits work?
Reply With Quote
  #3  
Old 07-31-2014, 09:04 AM
CalvaryCop CalvaryCop is offline
 
Join Date: Sep 2013
Posts: 296
Default

Mineral spirits comes from petroleum,Turpentine comes from a tree.
Reply With Quote
  #4  
Old 08-08-2014, 03:50 PM
Aladinbama Aladinbama is offline
 
Join Date: Nov 2009
Location: Pearland, Tx
Posts: 126
Send a message via AIM to Aladinbama
Default

Turpentine tends to be a cleaner solvent and that is the reason I always recommend it. I also have it on hand.
It's ok to use mineral spirits, it's just not my preference.
__________________
Please Visit My Web Page
www.thegunstockdoctor.com
Reply With Quote
  #5  
Old 12-21-2014, 12:00 PM
RASelkirk RASelkirk is offline
 
Join Date: Nov 2014
Location: SETX - 77651
Posts: 192
Default

Tom,

Bumping this back up to say thanks! I just watched all your vids on refinishing.

Russ
Reply With Quote
  #6  
Old 12-29-2014, 01:56 PM
ac57 ac57 is offline
 
Join Date: Nov 2010
Location: Tennessee
Posts: 217
Default

Tried your turpentine/BLO scrub on some milsurp stocks this weekend, very pleased with the results! Cleaned a bunch of grunk off and brought out the grain nicely.

Thanks for the tips!
Reply With Quote
  #7  
Old 07-09-2018, 06:58 PM
ZvenoMan ZvenoMan is offline
 
Join Date: May 2011
Location: AL
Posts: 3,718
Default

Bump to top because you need to read this :-)
JH
Reply With Quote
  #8  
Old 06-20-2019, 05:55 AM
Buckshotshoey Buckshotshoey is offline
 
Join Date: May 2019
Posts: 18
Default

Im waking up this old thread because I found something that works VERY well. I have an 1896 American Gun Co double barrel 28 ga. It belonged to my Great Great Grandmother. I think it was her 16th birthday present.

I restored it, and had a gunsmith check it out. Good to go! Some pitting on the outside but the bores are smooth as glass.

Anyway, I had to fix a crack in the forearm. Problem was, there was 120 years worth of oil (petroleum and human) soaked into the wood. I found this video from Larry Potterfeld. He soaks the wood in acetone. Didnt have much of a finish to strip, so i went ahead and tried it. And it looked like a fresh hunk of walnut. I ended up having to do the stock because of the mismatch. Then tung oiled both after the repair.

Acetone wont swell the wood, and evaporates completely in a short time.

https://youtu.be/Eb7WQTbXUlU

Last edited by Buckshotshoey; 06-20-2019 at 06:16 AM.
Reply With Quote
  #9  
Old 06-23-2019, 09:24 AM
mrjinglesusa mrjinglesusa is offline
 
Join Date: May 2019
Location: VA
Posts: 27
Default

Saw this old post bumped up and I needed to clean up some hand guards I purchased to match my SA/GAW stock. The rear hand guard was in nice shape but the front hand guard was very dirty, almost black. I used the OP method of 50:50 turpentine/BLO and that cleaned in up some, but not enough. Reading some other threads, I then used odor-less mineral spirits and that did the job perfectly. Really nice, red patina underneath all the dirt and grime.

I then applied a coat of raw linseed oil to the handguards and stock, let it sit an hour, wiped off excess, and let it fully cure/dry for 24 hours. REALLY happy with the results. Everything matches nicely with a “been there, done that”, red patina and have a beautiful, silky smooth finish.
Reply With Quote
  #10  
Old 09-21-2019, 10:27 PM
Tommiep54 Tommiep54 is offline
 
Join Date: Feb 2018
Location: Sylvania, Ohio
Posts: 319
Default

I'm considering trying this with turpentine and milk paint PTO. What do you think?



Sent from my SM-N950U using Tapatalk
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 04:10 AM.