Go Back   CMP Forums > CMP Competitions > 3-Position Air Rifle > Competitors Corner
Register FAQ Members List Calendar Mark Forums Read

Thread Tools Display Modes
Old 03-20-2014, 08:52 AM
CMPMikeD CMPMikeD is offline
Join Date: Feb 2014
Posts: 211
Default Did you know? - Pellet Sizes (Vogel USA)

The following is a write up done by Vogel USA and is a great explanation about how pellets are made and what all the fancy numbers mean.

Reference: Vogel USA

"The first thing you need to know is that competition air guns used in the Olympic disciplines are .177 caliber, which is equal to 177th thousandths of an inch. The metric equivalent to .177 inches is 4.50 millimeters, therefore the European caliber designation is 4.5 mm.

Next, you should know that the smallest quantity of match pellets are typically packaged as 500 pellets and are in containers called tins. When ten tins are packaged together, they are called a sleeve. A sleeve contains 5,000 pellets and weighs a little more than 6 pounds. Five sleeves packaged together are called a case. A case contains 25,000 pellets and weighs about 32 pounds. Case quantities are normally bought by schools, clubs, very serious competitors, or those stocking up early for Y3K.

So much for packaging. Next, you need to know that these .177 caliber or 4.50 mm match pellets are made in different sizes.

As a way of refining accuracy, and to most perfectly fit an individual group of pellets to the exact size and characteristics of your gun barrel, pellets are made in different head sizes. Head sizes start at 4.48 mm and continue through 4.49, 4.50, 4.51, and 4.52 mm. These sizes are determined by the various size molds used to create the pellets in the manufacturing process. But, you ask, isn't one .177 barrel the same size as another .177 barrel? No, not really.

In the barrel manufacturing process, the tolerances are such that the finished size of the lands and grooves of the rifling, will vary enough from one barrel to another that, while one barrel coming off of the assembly line might prefer the undersized pellets of 4.48 mm - the next barrel might be happier with oversized pellets of 4.51 mm.

In a perfect world, you would discover which head size fits your gun and that would always be the perfect pellet for your gun - but, we all know we don’t live in a perfect world. Nonetheless, a myth has arisen in the shooting world saying that a specific pellet head size is the only information you need to know to obtain maximum accuracy from a particular target airgun. This myth is derived from a misunderstanding of a small piece of paper that comes with every target airgun sold, that paper is called a test target.

The airgun manufacturers (Anschutz, Walther, Steyr, FWB, Morini, etc.) include a test target with each new airgun showing a very small group shot from that specific airgun. Generally, scribbled beside the group will be some initials denoting the mfg of the pellet (H & N, RWS, JSB, or Vogel) and a head size diameter (4.48, 4.9, 4.50, etc). It is a profound misunderstanding of this test target which causes so much confusion for parents, athletes and coaches.

Unfortunately, the conclusion of proper head size pellets for this particular airgun is drawn when the new owner opens up his or her prize new airgun and looks at the owner's manual for guidance and sees the head size written on the test target. The owner immediately thinks that it was selected by the factory as the perfect size pellet for use in this airgun, somewhat akin to Moses bringing the 10 commandments off of Mount Sinai. The reality is that head size on a factory test target has about as much relevance to your final decision on what is the most accurate pellet for your airgun as Bugs Bunny making that proverbial left turn in Albuquerque.

The test target is nothing more than a validation from the factory that this particular airgun is capable of shooting well. The factory IS NOT trying to determine the best pellet for your gun. In fact, as we will see in a moment, they cannot do this. What the gun factories want to do is put a sample of various pellets through their guns to see if they are shooting to their accuracy expectations. The test targets are shot with a group of five pellets. If they shoot the one group of five pellets and they get a great looking group, you can bet the next thing that gun will see is the inside of a packing box, not shooting more five shot groups of pellets.

Of course they will not always get a great looking group on the first attempt and often will shoot two or three different five shot groups of pellets to assess the accuracy of the gun/barrel combination. From that first two or three groups, they will take the best looking group, scribble down the manufacter and head size on that test target as a verification that it shot well. Then that airgun goes off for final packaging and is shipped to an airgun dealer near you.

If they shoot the first four groups and none of the groups are as tight as they should be, then they will shoot another sample of four groups possibly on the opposite extreme of the pellet size spectrum. Normally, for air rifles, one or more of these groups will be able to hold an unfired pellet up by skirt, when holding the target horizontally in the air. As soon as they find a good looking group, that target will go out with the gun. If none of these attempts show accuracy, then the gun will go back to have its barrel or regulator checked before coming back to the test range. The point is, shooting test targets are not attempts by the factory at defining what shoots well in their barrel, but only that their barrel does indeed shoot well.

Now then, if this head size number indicated on your gun’s test target is not the key to the accuracy then what is? How do you know what pellets you should buy? To really get true information requires testing your airgun from solid rest with a variety of head sizes and lot numbers. Lot numbers you say? What are those? Lot numbers are what are used by manufactures to differentiate between various groups of pellets having different production characteristics.

In firearms ammunition there are a lot more variables that can make-up a lot number change. Anything that is different in the production requires a new lot number. A change from one group of primers to another, a new box of gun powder, a change in brass, a change in the roll of lead wire used to make the bullet, a change in the adjustment of the machine, even a simple tweak will necessitate a new lot number. Often this means that single machine operating in a normal 8 hour work day could produce 5 or more different lot numbers.

For airgun pellets, there are really only two variables that create a different lot number, a change in the lead wire or a change in the machine adjustment. For us at Vogel USA, if everything goes well and an entire roll of lead wire runs through the machine without any machine tweaking taking place, then a lot will not be any larger than 12 sleeves, or approximately 60,000 pellets. If production is stopped in the middle of a roll of wire and a machine adjustment is made, then that creates a new lot number. If we stop again and make another machine adjustment, then that creates another new lot number. So you can see that its possible that lot number could cover only 2 or 3 sleeves of pellets.

To determine what a given pellet's lot number is, we normally only have to look at the tins, often they are stamped on little stickers on the bottom of the tin, and they will also be found on the corresponding sleeves and cases. It is important when choosing lots to be tested, that you determine if the supplier has a large enough quantity on hand of each lot number you test to actually supply you with that lot number in the event you choose it as the best shooting lot in your gun. Often, a supplier will have to hold back those lots being tested until you make your final purchase, so they won't sell out of the lot you eventually choose. In fairness to the vendors, you should do your pellet testing as soon as possible upon receiving the sample lots, so as not to tie up his inventory of pellets for weeks on end."

Follow us on Twitter: @cmpsouthrange
Like us on Facebook: www.facebook.com/CMPSouthRange
Google+: CMP South
Join the CMP Forum: http://forums.thecmp.org/forumdisplay.php?f=104
Email us: cmpsouthcomp@gmail.com
Reply With Quote
Old 06-19-2017, 09:34 PM
carrollms carrollms is offline
Join Date: May 2010
Location: Beattyville, Kentucky
Posts: 24

Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 08:05 AM.